How to assemble a chest of drawers

How to build a chest drawer? Step 1: Cutting the Panels. The first step was to cut out the panels for the carcass. Add Tip Ask Question Comment Download.

Make a sketch or to -scale drawing of the chest of drawers you would like to make. Include measurements of the outer box and decide how many drawers you will have.

Measure the drawer area and mark the approximate depth and width for each drawer. See full list on doityourself. After careful measurement, use a straightedge and a pencil to mark the pieces for the exterior cabinet. Cut a bottom piece and a top piece of the same size, and two side pieces of the same size.

Do a quick layout of your pieces to ensure that they will sit together properly. Then, following your measurements for the height of your drawers (specifically your drawer fronts since this will be the widest part), figure out where to position the drawer slides. Align them exactly, one on each side, and screw them to the cabinet. Using the L-brackets on the top and bottom pieces, attach the sides to the bottom.

Use the drywall screws and wood glue to secure it well.

You can add legs or decorative supports to the bottom of the chest of drawers at this time, or you can add something later if you choose. This chest can sit on the floor as well. Also make sure that both sides have been attached correctly with the drawer slides right-side up. Lastly, attach the back panel with finishing nails. Carefully measure the space between the two sides, and cut a piece of plywood to fit, nailing them in place with finishing nails.

It is possible, however, to construct a chest where the drawer fronts create the front of the chest with no panels between them. It comes down to personal preference, so decide how you want your drawers to look. To allow the drawer to fit in the slides, make the total width of the box one inch smaller than the width of the space of the opening of the dresser.

Use a router to create a joint in for attaching the backs and fronts. Finish securing the back and two sides to one another with wood glue and finishing nails. Measure the inside dimensions of the basic drawer frame and add the depth of the groove you cut. Coat the inside of the groove with wood glue and slide the drawer bottom in place.

Finally attach the front of the box to the rest, followed by the decorative drawer fronts. Use decorative molding on the sides, front, or bottom of the chest of drawers , and add a finish to the wood with a paint or stain. Make any fine tuning adjustments as needed. Pull your bottom Drawer out all the way look on the side of the drawer ther is a slot on each side push a small screwdriver into the slot and pull drawer out one side at a time small amounts! When all else failsread owners manual!

Are you sure you have the right space that goes there?

That you didn t use it in the wrong place? Build a chest of drawers - Part of 30. Click through to watch this video on expertvillage. Then adjust the chest carcass till it is aligned with the other edge of the back panel. They are as easy to assemble and come in a knockdown format for easy transportation.

Great Selection of Yellow Bedroom Furniture! Attach the drawer slides following the manufactures directions. Free Shi pp ing on Orders over $35. Shop Yellow Bedroom Furniture! Free 2-day Shi pp ing On Millions of Items.

Decide on how big the chest of drawers is going to be and how many drawers will it have. The chest shown here had to. Assemble the bottom panel. Cut the pieces for the Drawer Guides. Insert the wood screws from the inside of the Chest, through the Drawer Guides, into the Chest Sides so that the screws are hidden.

Drill pocket holes in the both ends of the ¼ inch length drawer pieces. Join the inch pieces to the ¼ inch lengths to form the drawers. I routed the sides to fit a ¼ inch plywood base. Recently, my in-laws were doing some cleaning and had old furniture they no longer wanted.

Luckily for me my hubby knew exactly where to take it. One of the pieces was this small chest of drawers. Believe or not this was made of mahogany!

As you can tell from the photo, this piece definitely needed a good cleaning. I was going to make a small bench with this foot boar but I wanted to give it a drawer for storage. I had a couple of drawers that I could use, but I didn’t really know how to “frame” them out.

Then it hit me, why not used the drawers in their existing “frame” AKA the chest of drawers. See more ideas about Redo furniture, Diy furniture, Furniture makeover. Christian Becksvoort makes the construction easy with smart solutions to cutting dadoes, dovetails, and adding a smooth runner system for the drawers. Because of the construction of the chest , I had to trim off a little of each of the front facings.

It went from drawers to shelves. I removed the chunky 2×from across the bottom front, I’m not really sure why it was there.